Our Recent Work

Tampa, Hillsborough County · October 2026

A GulfStream HE150-RA in a tight gravel side yard, set on a level base the crew built from concrete block before the unit went in.

Siesta Key, Sarasota County · October 2026

A heat-only GulfStream HE150-RA set beside a Pentair automation panel, filter and pump in a tight barrier-island equipment area.

Punta Gorda, Charlotte County · October 2026

The smallest model in GulfStream's HE line, an HE110-RA, set beside the house and plumbed in fresh PVC with unions at the heater.

Treasure Island, Pinellas County · October 2026

A GulfStream HE150-RA on a concrete pad in a rock bed on a Pinellas barrier island, plumbed with short, square PVC runs.

Sarasota (Manatee County side) · October 2026

A Hayward heat pump set on the concrete equipment slab beside the filter, finished with a walk-through of the controls with the homeowner.

Lakeland, Polk County · October 2026

A Hayward heat pump on a concrete pad between the house and a paver walk, tied into a valve manifold that keeps every line reachable.

Hudson, Pasco County · October 2026

A Hayward heat pump on its own pad in an open, walled yard, with long PVC runs back to the pool equipment.

Babcock Ranch, Charlotte County · October 2026

A Pentair MasterTemp gas heater on a full equipment pad with a cartridge filter, variable-speed pump and labeled suction and return valves.

Lehigh Acres, Lee County · October 2026

Solar pool heating collectors on a shingle roof beside a screened pool, with the supply and return lines run along the roof edge.

Dunedin, Pinellas County · September 2026

A heat-only GulfStream HE150-RA set on its own pad along the side of the house and plumbed back to the filter and valve manifold on the main equipment pad.

Largo, Pinellas County · September 2026

Two banks of solar pool heating collectors on a shingle roof, with the supply and return lines run in white PVC across the roof to the pool equipment.

Lakewood Ranch, Manatee County · September 2026

Solar pool heating collectors on two shingle roof planes, plumbed with dark supply and return lines that blend in with the roof.

A Hayward gas heater set on a concrete pad in a mulch bed beside the house, with the gas line run along the wall to the heater and the cartridge filter, pump and valves on the pad behind it.

A Hayward gas heater tucked into a corner on its own pad, with the gas regulator and metal gas piping on the wall beside it and the PVC water connections coming off the front.

A new Pentair MasterTemp, EnergyGuide label still on the cabinet, set on a rust-stained concrete pad and plumbed into a PVC valve manifold, with the gas line coming in from the left.

A pool pump and filter on a concrete pad in front of a heat pump, along a stucco side wall, with short PVC runs tying the three together.

Solar collectors laid out across the roof, strapped down over the rafters and tied into the header and return runs. The clips show the crew setting a panel and the finished array soaking up the Florida sun.

A Jandy heat pump set on a fresh pad beside a new Pentair cartridge filter and pump. Every valve sits at the same height and faces forward, so the whole system reads at a glance.

A Pentair gas heater dropped into a narrow side yard. The gas line and PVC all had to thread past the existing filter and valves without crowding the service clearances.

A heat pump set on a level base just outside the lanai, with a short PVC run back to the pad and the disconnect mounted within easy reach. Sited for clear airflow on all sides so it holds efficiency year-round.

A new variable-speed pump swapped in alongside the homeowner's existing Hayward cartridge filter, with the cartridge pulled and cleaned while we had the system open.

Recent work in Sarasota, Florida, a new Hayward gas heater plumbed into the equipment pad with clean, easy-to-service PVC runs.

A new pump and a Jandy salt cell plumbed in alongside the existing cartridge filter, with the PVC runs kept short, square and easy to service. Shot on site while the work was underway.

Solar collectors mounted on the roof and plumbed down to the pool equipment, turning the Florida sun into months of extra swimming with essentially no fuel cost to run.

A Pentair heater paired with a fully re-plumbed valve manifold. Every line is squared up and easy to reach, so servicing this pad down the road is straightforward.

The customer wanted a locally manufactured heater, and GulfStream is made right in North Fort Myers, Florida. We installed it alongside the existing filter and pump for efficient, thermostatically controlled pool heating.

A full rebuild of the pool's plumbing with new valves, a new electric heater and automation, plus pool solar to help hold the heat and lower the operating cost of the electric heater. Completed in 2024.

Completed in 2025, this customer wanted a Hayward heater and pool equipment plumbing that is clean and aesthetically pleasing.

Completed in May 2026. A Hayward gas heater set on its own pad beside the home, plus a Jandy TruClear salt chlorine system added as part of the same project.

A project in Naples, Florida where the customer wanted to add a gas heater and redo all of the plumbing equipment.

A GulfStream pool heat pump, manufactured in North Fort Myers, Florida, set on the equipment pad and plumbed into the existing filter and pump.

A project on Siesta Key in Sarasota. The homeowner wanted his pool equipment elevated, and we made it happen affordably.